Invisible Chewing Gum and Stain Repellent
The Ultimate in Pavement and Floor Protection!
Due to its exceptional penetration and stain repellent properties, Pave-Saver, supplied by Go-Gum Limited, is ideally suited to the protection of a wide variety of outdoor and indoor masonry surfaces that are subjected to heavy foot traffic.
Pave-Saver protects surfaces from weathering and helps surfaces remain clean by repelling chewing gum, water, airborne dirt, acid rain, smog, industrial pollutants, oil and grease, dust and organic growth (lichens & moss).
Rain water will remove most stains as the pollutant is prevented from sticking to the substrate. Pave-Saver offers this high level of protection by effectively reducing the adhesion rate of the pollutant, whilst still enabling the underlying materials to breathe. Once treated, pressure washing/steam cleaning with the Enviraclean Machine/Gum-Grafter (or similar) may be required periodically.
Pave-Saver also prevents spalling through repeated freeze/thaw cycles. Once applied it is invisible, essentially forming part of the substrates fabric and therefore offering high resistance to abrasion.
Benefits
- Years of efficient protection against chewing gum,water, oil, moss, carbon particulates, dirt, bird droppings and stain penetration.
- Water & oil repellent
- Stain resistant
- Abrasion resistant
- Non-hazardous
- Non-toxic
- Non-flammable
- Water based
- Environmentally friendly
|
|
- Solvent free
- Silicone free
- Invisible when dry
- Allows surfaces to breath (vapour permeable)
- High and lasting UV resistance
- Non-staining and non-yellowing
- Reduces surface degradation
- De-icing salt resistant
- Acid and alkali resistant
- No affect on slip resistance
- Ready to use and quick to apply
|
Areas of Use
Pave-Saver can be applied to pavements, pedestrian areas, forecourts, car parks, roofs, terraces, floors, stairs - practically any high traffic masonry area which requires protection!
Technical Specifications
Appearance: Liquid
Colour: Amber
Odour: Very Subtle
Active: Agents
pH value: 5-6
Boiling Point [°C]: 100
Density: 1.01
Flash point [°C]: Not applicable
Solubility in water [°C]: Totally miscible
Product Description
A water based fluorochemical dispersion.
Application Guide
Surface to be treated must be free from chewing gum, dust, dirt, oil, efflorescence, mould/algae, old paint, other surface contaminants.
Clean surface thoroughly using a hot wash/pressure washer (Go-Gum Enviraclean Machine or similar) prior to application. The substrate should be dry, with surface and ambient temperatures between 5ºC and 35ºC.
Pave-Saver can be applied by brush, roller, squeegee, back pack sprayer or low pressure spray.
Surface to be treated must be fully saturated. This will require between 1 and 3 coats applied wet on wet dependant on substrate porosity (see guide).
Substrates for Treatment
- Paving Stones
- Concrete
- Brick
- Block Paving
- Sandstone
- Granite
- Marble
- Limestone
- Terracotta
- Roof Tiles
- Slate
- Any Porous Mineral Substrate
|
|
Consumption Rate Guide*
Paving Stones: 5 m2/L
Concrete: 5 m2/L
Brick: 3 m2/L
Block Paving: 9 m2/L
Sandstone: 1-5 m2/L
Granite: 26 m2/L
Marble: 16 m2/L
Limestone: 1-5 m2/L
Terracotta: 7.0 m2/L
Roof Tiles: 10 m2/L
Slate: 8 m2/L
*Approximate values. Test areas should always be
undertaken to establish site specific consumption rates.
|
How Pave-Saver Protects
Pave-Saver is not a coating, and therefore does not suffer from failure due to adhesion issues.
Pave-Saver treatment is achieved by impregnation to the point of saturation so that Pave-Saver gets deep into a material's pores, thus making it water repellent. In preventing the ingress of water, Pave-Saver removes the damaging effects of both frost and humidity.
Product Demonstration
Should you require a no obligation demonstration of Pave-Saver please contact us on 020 7566 3988. We are happy to visit you at your place of work or an agreed location in order to demonstrate the unique cleaning and protection solutions offered by Go-Gum limited.
|
