» Home
» Company
» Media Centre
» Contact
» eMail
» Links

» Enviraclean Range
» Benefits of Enviraclean
» Enviraclean in Action

» Gum-Grafter
» Grime-Grafter

» Street Cleansing Team

» easy-on
» easy-guard

» Pave-Saver

FIRE SAFETY LAW IS CHANGING
IN OCTOBER 2006

New fire safety rules affecting all non-domestic premises in England and Wales (United Kingdom) came into force on 1 October 2006. If you are:

• responsible for business premises
• an employer or self-employed with business premises
• a charity or voluntary organisation
• a contractor with a degree of control over any premises

... then you need to act now to ensure you have a suitable and sufficient risk assessment in place.

For further details please visit the Department for Communities and Local Government.

The fire resistant coating for ultimate wall protection

Highly effective fire retardent technology

When lives are at stake you must be assured that you have the best possible fire protection available.

easy-guard is a revolutionary fire retardant coating that is safe and easy to use. It can be applied over any existing paintwork and is available in a wide range of colours designed to improve and enhance the living environment.

Water based easy-guard is fully compliant with all fire standard regulations and in the worst case Warrington blue board test achieves a Class '0' rating in just 3 coats.

For maximum durability easy-guard can be over coated with easy-on protective coating. This complete system will provide over 20 years protection from graffiti, scuffing, bacteria and damage.

With its durable top coat, even graffiti removal can be carried out on a daily basis without compromising the fire protection finish, a common problem with other systems.

Ultimate fire and wall protection for over 20 years - easy-guard + easy-on.

Buy easy-guard Online

easy-guard Fire Upgrading System

Where inter-coat adhesion is good and on site risk assessment is low/moderate, use easy-guard Fire Upgrade System, comprising one primer and one colour coat (unless strong colours required). Fire Upgrade is a water based, low odour, single pack. Fire Upgrade system produces class 1 and Class 0 on plasterboard and also successfully upgrades the worst case scenario flammable Class 4 Warrington "Blue" Boards to Class 1.

Application Guide

1. Attend site and carry out adhesion tests to all pre-painted wall and ceiling surfaces.
2. Identify any areas of weak intercoat adhesion and scrape back to a hard edge.
3. Feather off as necessary and fill holes or hollows using a high quality filling compound.
4. Thoroughly abrade all glossy/hard surfaces. Wash down and degrease with easy-guard Wash Down Agent and rinse with clean water.
5. Spot prime any bare or filled patches with one coat of easy-guard Fire Upgrading Primer thinned 10% with clean water.
6. Apply 1 full coat of easy-guard Fire Upgrading Primer by brush/roller at a coverage rate of 8m²/ litre. Allow at least 24 hours drying time.
7. Apply 1 full coat of easy-guard Fire Upgrading Colour Coat by brush/roller at a coverage rate of 8m²/ litre. Allow at least 24 hours drying time.
8. Apply one coat of easy-on protective coating by brush or roller at a rate of 30m²/litre

easy-guard CLASS "0" System

Where the risk assessment shows that multi layered paint is considered to be highly flammable and poses a severe flame spread and fire risk use easy-guard Class "0" Barrier system. Comprising water based primer, barrier compound and colour coat it upgrades the worst case scenario flammable Class 4 Warrington "Blue" Board to Class 1 and Class 0. The use of the Class "0" barrier system in this case is essential.

Application Guide

1. Attend site and carry out adhesion tests to all pre-painted wall and ceiling surfaces.
2. Identify any areas of weak intercoat adhesion and scrape back to a hard edge.
3. Feather off as necessary and fill holes or hollows using a high quality filling compound.
4. Thoroughly abrade all glossy/hard surfaces. Wash down and degrease with easy-guard Wash Down Agent and rinse with clean water.
5. To clean dry surfaces apply one coat of easy-guard Class "0" Bond Primer by brush or roller at a coverage rate of 14-16m²/ litre. Allow at least 1 hour drying time.
6. Apply 1 coat of easy-guard Class "0" Barrier Compound by brush/roller at a coverage rate of 0.45m²/litre. Pattern as necessary and lace down when hard dry.
7. Apply 1 full coat of easy-guard Class "0" Colour Coat by brush/roller rate of 6-12m²/ litre. Allow at least 8 hours drying time.
8. Apply one coat of easy-on protective coating by brush or roller at a rate of 30m²/litre

Easy Guard Price List

Buy easy-guard Online

Product Demonstration

Should you require a no obligation demonstration of the easy-guard™ protective coating please contact us on 020 7566 3988. We are happy to visit you at your place of work or an agreed location in order to demonstrate the unique cleaning and protection solutions offered by Go-Gum limited.

* Approximate Coverage.